Pumps, piping & valves · Free tool
Pipe sizing and pressure drop calculator
Pick a line size for water, process liquids, saturated steam or gas. Enter the flow and the calculator shows the velocity and pressure drop in each nearby pipe size, and suggests the smallest size within recommended velocity.
1. Fluid and flow
2. Pipe
Schedule
Bends, valves, tees
Suggested size
80 NB
3 inch, Sch 40
Velocity
1.75m/s
Target 1–2.5 m/s
Pressure drop
0.498bar
over 130 m equivalent
| Size | ID mm | Velocity m/s | Reynolds | ΔP bar/100 m |
|---|---|---|---|---|
| 50 NB (2") | 52.5 | 3.85 | 2,51,616 | 2.856 |
| 65 NB (2 1/2") | 62.7 | 2.70 | 2,10,684 | 1.153 |
| 80 NB (3") | 77.9 | 1.75 | 1,69,575 | 0.383 |
| 100 NB (4") | 102.3 | 1.01 | 1,29,129 | 0.098 |
| 125 NB (5") | 128.2 | 0.65 | 1,03,041 | 0.032 |
Density used 996 kg/m³, viscosity 0.8 cP, mass flow 29,880 kg/h. Target velocity midpoint 1.75 m/s.
Want these numbers checked?
Send them to a SEMCO process engineer for a free review, sizing and budget price.
How this calculator works
For each standard pipe size, the calculator divides the volumetric flow by the bore area to get the velocity. It then works out the Reynolds number from density, velocity, bore and viscosity, which tells whether the flow is laminar or turbulent.
The Darcy friction factor comes from the Swamee-Jain equation, an explicit form of the Colebrook equation, for turbulent flow, and 64/Re for laminar flow. The Darcy-Weisbach equation then gives the pressure drop. Fittings are added as a percentage of equivalent length.
For saturated steam the density is taken at your line pressure from the steam table calculator. Bore sizes follow ASME B36.10 (Schedule 40) and B36.19 (Schedule 10S).
Formulas used
Velocity
Reynolds number
Swamee-Jain friction factor (turbulent)
Darcy-Weisbach pressure drop
Assumptions and limits
- Single-phase, incompressible flow. For steam and gas this holds when the pressure drop is under about 10 percent of line pressure.
- Fittings are an allowance on length. For long or complex lines, add each fitting's equivalent length or K value.
- Water properties at about 30 °C. Hot water has lower viscosity, which slightly reduces pressure drop.
- Elevation changes, control valves and equipment pressure drops are not included.
Worked example
30 m³/h of cooling water through 100 m of carbon steel Sch 40 pipe with 30 percent extra for fittings.
- Try 80 NB (77.9 mm bore): area 0.00477 m², velocity = (30/3,600) ÷ 0.00477 ≈ 1.75 m/s, inside the 1–2.5 m/s range.
- Reynolds number = 996 × 1.75 × 0.0779 ÷ 0.0008 ≈ 170,000, turbulent.
- Friction factor from Swamee-Jain with 0.045 mm roughness ≈ 0.0196.
- Pressure drop ≈ 0.0195 × (130 ÷ 0.0779) × 996 × 1.75² ÷ 2 ≈ 0.50 bar over the line.
Frequently asked questions
What velocity should water flow at in a pipe?
About 1 to 2.5 m/s on pump discharge lines, and 0.6 to 1.2 m/s on pump suction to protect against cavitation. Long lines are often sized at the lower end to save pumping power.
What velocity is recommended for steam pipes?
Saturated steam mains are usually sized for 15 to 35 m/s. Higher velocities cause noise, erosion and large pressure drops; wet steam and condensate lines need lower velocities.
What is the difference between Schedule 40 and 10S?
They have the same outside diameter but different wall thickness. Schedule 40 is common for carbon steel; Schedule 10S is a thinner stainless steel pipe with a slightly larger bore.
Why does the pressure drop rise so fast with smaller pipe?
For a fixed flow, pressure drop rises roughly with the fifth power of the diameter going down. Going one size smaller can double or triple the pressure drop.
Need it designed and built?
SEMCO designs, fabricates and commissions evaporators, ZLD plants, heat exchangers, reactors and vacuum systems in its own factories in Pune and Solapur.
Related tools
Saturated steam table calculator
Temperature, pressure, enthalpy, latent heat and specific volume of saturated steam, in bar(g), bar(a), kg/cm² or psi.
Process engineering unit converter
Pressure and vacuum (gauge and absolute), flow, energy, heat transfer coefficient, viscosity and more.
Vacuum pump-down time calculator
How long a vacuum pump takes to evacuate a vessel, or the pump size you need for a target time.
Results are engineering estimates for early sizing and budgeting. Final designs depend on your liquid, site and codes, and are confirmed in SEMCO's proposal. Method reviewed by Jogender Dhayal, Director, SEMCO.