Pumps, piping & valves · Free tool
Pump head, power and NPSH calculator
Work out the total head a centrifugal pump must deliver, the shaft power and motor size, and whether there is enough NPSH to avoid cavitation. Enter your suction and discharge conditions the way they appear on a P&ID.
1. Flow and liquid
2. Suction side
0 for an open tank; negative for vacuum.
Negative if the liquid is below the pump (suction lift).
3. Discharge side
Use the pipe sizing calculator for line losses.
4. Pump and motor
Small centrifugal pumps 40–65%, large 70–85%.
Total head
39.9m
3.91 bar differential
Shaft power
4.18kW
Hydraulic 2.72 kW
Suggested motor
5.5kW
Shaft power + 15%
| Static head (elevation) | 13 m |
|---|---|
| Pressure head | 20.39 m |
| Friction head | 6.5 m |
| NPSH available | 11.08 m |
| Vapour pressure used | 0.0739 bar(a) |
| Flow | 25 m³/h = 6.94 L/s |
Want these numbers checked?
Send them to a SEMCO process engineer for a free review, sizing and budget price.
How this calculator works
Total head is the energy per unit weight the pump has to add: the pressure difference between the discharge and suction vessels converted to metres of liquid, plus the difference in elevation, plus the friction losses in both lines.
Hydraulic power is density × g × flow × head. Dividing by pump efficiency gives the shaft power; the motor is sized 15% above that and rounded up to the next standard IEC rating.
NPSH available is the absolute pressure at the pump suction, above the liquid's vapour pressure, expressed as head. It is compared with the NPSH the pump needs, from its curve. For water the vapour pressure comes from the steam table at your temperature.
Formulas used
Total dynamic head
Shaft power
NPSH available
Assumptions and limits
- Single-phase liquid with constant density; velocity heads at the vessel surfaces are taken as zero.
- Friction losses are entered by you; use the pipe sizing calculator for straight runs and fittings.
- Motor margin of 15% covers off-design operation and wear; increase it for viscous or slurry duties.
- NPSH margin guidance (at least 1 m or 10–30% above NPSHr) follows common practice; follow the pump maker's rule for critical services.
Worked example
25 m³/h of water at 40 °C from an open tank with 2 m of liquid above the pump to a point 15 m above the pump at 2 bar(g).
- Pressure head = (2 − 0) bar ÷ (1,000 × 9.81) ≈ 20.4 m.
- Static head = 15 − 2 = 13 m; friction = 0.5 + 6 = 6.5 m; total head ≈ 39.9 m.
- Hydraulic power = 1,000 × 9.81 × 0.00694 × 39.9 ≈ 2.72 kW; at 65% efficiency the shaft needs about 4.2 kW, so a 5.5 kW motor.
- NPSHa = (1.013 − 0.074) bar as head (≈ 9.6 m) + 2 − 0.5 ≈ 11.1 m, comfortably above a 3 m NPSHr.
Frequently asked questions
How do I calculate pump head?
Add the pressure difference between discharge and suction (converted to metres of liquid), the elevation difference, and the friction losses in the suction and discharge lines. 1 bar is about 10.2 m of water.
What is a good NPSH margin?
Keep NPSH available at least 1 m, or 10–30%, above NPSH required. Hot liquids, liquids near their boiling point and suction lift duties need extra care.
How do I choose the motor size?
Divide hydraulic power by pump efficiency to get shaft power, add 10–20% margin and select the next standard motor rating.
Why does my pump cavitate even though NPSHa looks fine?
Common causes are a blocked suction strainer, a higher liquid temperature than assumed, entrained gas, or the pump running far to the right of its curve where NPSHr rises sharply.
Need it designed and built?
SEMCO designs, fabricates and commissions evaporators, ZLD plants, heat exchangers, reactors and vacuum systems in its own factories in Pune and Solapur.
Related tools
Pipe sizing and pressure drop calculator
Velocity, Reynolds number, friction factor and pressure drop for liquids and steam, with recommended pipe size.
Reynolds number calculator
Reynolds number, flow regime, friction factor and pressure drop per 100 m for pipe flow.
Control valve Cv and Kv sizing
Required Kv and Cv for liquid, gas and steam, with choked-flow check and a typical valve size.
Results are engineering estimates for early sizing and budgeting. Final designs depend on your liquid, site and codes, and are confirmed in SEMCO's proposal. Method reviewed by Jogender Dhayal, Director, SEMCO.