Pumps, piping & valves · Free tool
Safety valve sizing calculator (API 520)
Size a pressure safety valve for gas, vapour, steam or liquid relief. Enter the relieving rate and set pressure to get the required orifice area and the API 526 orifice letter.
1. Relieving fluid
Fluid
Air 28.96, N₂ 28.0, CO₂ 44.0, CH₄ 16.0
2. Relief conditions
10% single valve, 16% multiple valves, 21% fire case
Required orifice area
527.5mm²
0.8176 in²
API 526 orifice
J
Effective area 830.3 mm²
Relieving pressure
11bar(g)
| Relieving pressure P1 | 12.013 bar(a) |
|---|---|
| Gas constant C | 0.02703 |
| Critical flow pressure | 6.346 bar(a) |
| Discharge coefficient Kd | 0.975 |
API 526 effective orifice areas
| Letter | Area mm² | Area in² |
|---|---|---|
| D | 71 | 0.11 |
| E | 126.5 | 0.196 |
| F | 198.1 | 0.307 |
| G | 324.5 | 0.503 |
| H | 506.5 | 0.785 |
| J | 830.3 | 1.287 |
| K | 1,185.8 | 1.838 |
| L | 1,840.6 | 2.853 |
| M | 2,322.6 | 3.6 |
| N | 2,800 | 4.34 |
| P | 4,116 | 6.38 |
| Q | 7,129 | 11.05 |
| R | 10,323 | 16.001 |
| T | 16,774 | 26 |
Want these numbers checked?
Send them to a SEMCO process engineer for a free review, sizing and budget price.
How this calculator works
The relieving pressure is the set pressure plus the allowable overpressure (10% for a single valve in most cases), converted to absolute pressure.
Gas and vapour relief uses the API 520 Part I critical flow equation with the coefficient C from the specific heat ratio. Steam uses the Napier equation, with the KN correction above about 103 bar(a). Liquid relief uses the API 520 equation for certified liquid-trim valves.
The required area is then matched to the next standard API 526 orifice (D to T).
Formulas used
Gas or vapour (critical flow)
A in mm², W in kg/h, P1 in kPa(a), T in K. C = 0.03948 √(k (2/(k+1))^((k+1)/(k−1))).
Saturated steam (Napier)
Liquid
Q in L/min, pressures in kPa.
Assumptions and limits
- Kd = 0.975 for gas and steam, 0.65 for liquid; Kb, Kc, Kw and Kv = 1 (conventional valve, no rupture disc, low viscosity).
- Gas flow is critical (back pressure below the critical flow pressure); a warning appears if it is not.
- The relieving rate must come from your overpressure scenario analysis (blocked outlet, fire, control valve failure and so on).
- Inlet and outlet piping pressure losses (3% inlet rule, built-up back pressure) are not checked.
Worked example
5,000 kg/h of air at 50 °C, set pressure 10 bar(g), 10% overpressure.
- P1 = 10 × 1.1 + 1.013 = 12.01 bar(a) = 1,201 kPa(a).
- For k = 1.4, C = 0.02703.
- A = 5,000 ÷ (0.02703 × 0.975 × 1,201) × √(323 × 1 ÷ 28.96) ≈ 528 mm².
- The next API 526 orifice is J (830 mm²), since H (506 mm²) is too small.
Frequently asked questions
What is API 520?
The American Petroleum Institute's standard for sizing, selecting and installing pressure-relieving devices. Part I covers sizing; API 526 lists standard orifice areas.
What overpressure should I use?
Typically 10% for a single valve, 16% when several valves protect the same vessel, and 21% for fire cases, within the code's limits.
Can I size a valve for two-phase relief with this tool?
No. Two-phase relief, such as runaway reactions or flashing liquids, needs methods like API 520 Annex C or DIERS.
Need it designed and built?
SEMCO designs, fabricates and commissions evaporators, ZLD plants, heat exchangers, reactors and vacuum systems in its own factories in Pune and Solapur.
Related tools
Pressure vessel thickness (ASME VIII-1)
Shell and head thickness under internal pressure, corrosion allowance, plate selection and MAWP.
Control valve Cv and Kv sizing
Required Kv and Cv for liquid, gas and steam, with choked-flow check and a typical valve size.
Gas flow conversion (Nm³/h, m³/h, kg/h)
Convert between Nm³/h, Sm³/h, actual m³/h at line conditions, kg/h and SCFM.
Results are engineering estimates for early sizing and budgeting. Final designs depend on your liquid, site and codes, and are confirmed in SEMCO's proposal. Method reviewed by Jogender Dhayal, Director, SEMCO.