SEMCO
Get a Quote

Agitators & mixing · 4 free tools

Agitator design calculations for reactors and mixing tanks

Choose and size the right agitator: impeller type and dimensions, speed, power and motor, solids suspension, blend time and scale-up from pilot to plant. Built by the engineers who design and fabricate SEMCO's reactors and agitators.

  • 8 impeller types with standard dimensions
  • Compare designs side by side
  • Formulas shown, no sign-up

Agitator calculators

Start here

Agitator design and comparison tool

Enter your reactor and liquid, pick impellers: get standard dimensions, speed, power, motor, torque, blend time, Njs and h, and compare up to four designs.

Impeller sizesrpmkW and motorBlend timeSide-by-side
Open the design tool

Which tool do I need?

Standard impeller dimensions and power numbers

Typical proportions for standard designs in a baffled vessel (anchors and ribbons unbaffled). These are the starting values the design tool uses; makers' figures vary by a few per cent.

ImpellerFlowD/TC/TPower number NpPumping number NqBest for
Pitched blade turbine (45°, 4 blades)Axial0.40.251.270.79General-purpose blending and solids suspension; good all-rounder.
Hydrofoil (high-efficiency, 3 blades)Axial0.40.250.30.56Most flow per kW; best for blending and solids suspension in low-viscosity liquids.
Rushton disc turbine (6 flat blades)Radial0.330.3350.72High shear and gas dispersion; high power for the flow it gives.
Marine propeller (3 blades, pitch = D)Axial0.30.250.350.4Small, fast, low-cost; suits small tanks and thin liquids.
Flat blade paddle (2 blades)Radial0.60.21.70.4Simple and slow; gentle mixing of moderately viscous liquids.
Retreat curve (3 blades, glass-lined style)Radial0.60.080.60.35Standard in glass-lined reactors; low shear, easy to clean.
Anchor (close clearance)Tangential0.950.030.35–Sweeps the wall for heat transfer in viscous batches; weak top-to-bottom mixing.
Double helical ribbonAxial (laminar)0.950.030.35–Best blender for very viscous liquids and pastes; slow and high torque.

How to design an agitator in six steps

  1. Define the duty: blending, heat transfer, solids suspension, gas dispersion, liquid-liquid dispersion or viscous mixing. The duty decides the impeller and the speed.
  2. Get the liquid properties at process temperature: density, and above all viscosity. Viscosity decides the flow regime and whether a turbine can work at all.
  3. Choose the impeller type: axial hydrofoils and pitched blades for flow, radial turbines for shear and gas, anchors and helical ribbons for viscous batches.
  4. Fix the geometry: impeller diameter (D/T), bottom clearance, number of impellers for the liquid height, and baffles.
  5. Set the speed for the duty, then calculate the Reynolds number, power number, shaft power, power per volume and torque.
  6. Size the drive and mechanics: motor with gearbox losses and margin, gearbox ratio, shaft diameter, critical speed, bearings and seal.

Key agitator formulas

Impeller Reynolds number

Re=ρND2μ

Shaft power

P=Np ρ N3D5

Torque and tip speed

τ=P2πN, vtip=πDN

Blend time, turbulent (Grenville)

θ95=5.2N1/3pN(TD)2

Just-suspended speed (Zwietering)

Njs=S ν0.1(g ΔρρL)0.45X0.13d0.2pD−0.85

Scale-up at constant P/V

N2=N1(D1D2)2/3

Frequently asked questions

How is an agitator designed?

Start from the mixing duty and the liquid viscosity, choose the impeller type, set its diameter, clearance and number of impellers, find the speed that achieves the duty, then calculate power, torque and motor size and finish with the shaft, gearbox and seal. The agitator design and comparison tool on this page walks through these steps and compares up to four impellers.

What is the standard diameter of an agitator impeller?

Turbines and hydrofoils are usually 0.3 to 0.5 times the vessel diameter: about 0.33 for a Rushton turbine and 0.4 for pitched blade and hydrofoil impellers. Anchors and helical ribbons are about 0.95 times the vessel diameter, running close to the wall.

What is the power number of an impeller?

It is the dimensionless constant linking power to speed and diameter in turbulent flow. Typical baffled values are about 5 for a six-blade Rushton turbine, 1.3 for a 45° four-blade pitched blade turbine and 0.3 for a hydrofoil. In laminar flow the power number rises steeply as Reynolds number falls.

Which impeller is best for high-viscosity liquids?

Above about 5,000 to 10,000 cP, turbines only mix near the blades. Anchors scrape the wall and suit heat transfer, while double helical ribbons give the best top-to-bottom mixing for very viscous liquids and pastes.

How many impellers does a tall reactor need?

Roughly one impeller for liquid height up to 1.2 times the vessel diameter, two up to 1.8 and three up to 2.5, spaced about 1 to 1.5 impeller diameters apart.

How much power does an agitator need per cubic metre?

As a rough guide: 0.05 to 0.2 kW/m³ for gentle blending, 0.2 to 0.6 kW/m³ for solids suspension and general reactions, 1 to 2 kW/m³ for liquid-liquid dispersion and 1 to 3 kW/m³ for gas dispersion. The calculators work out the actual figure for your vessel and duty.

Agitators built for your reactor

SEMCO designs and fabricates top-entry agitators, reactors and complete agitated systems in its own factories in Pune and Solapur, with drives, shafts and seals sized for your process.