SEMCO
Get a Quote

Agitators & mixing · Free tool

Agitator power, torque and motor size calculator

Estimate the power an agitator draws in a reactor or tank, the shaft torque and tip speed, and the motor size to specify. Works for water-thin liquids through to viscous pastes with anchors.

Shaft kWMotor kWTorqueTip speed
Designing a new agitator?The agitator design and comparison tool sets standard impeller dimensions and speed for your duty, and compares up to four impellers side by side.Open the design tool →

1. Impeller

m
rpm
m

2. Liquid and vessel

kg/m³
cP

Water 1, glycerine ~1,000

m³

3. Drive

%
%

Start-up, viscosity rise

Suggested motor

2.2kW

1.96 kW needed

Shaft power

1.48kW

Power per volume

0.18kW/m³

Blending and moderate heat transfer

Details
Impeller Reynolds number20,160 (Turbulent)
Power number used1.27
Shaft torque157 N·m
Tip speed3.77 m/s
Impeller / vessel diameter (D/T)0.36
Flow patternaxial
Values assume a baffled vessel (four baffles of T/10). Without baffles, turbulent power numbers can be 50–70% lower and a vortex forms.

Want these numbers checked?

Send them to a SEMCO process engineer for a free review, sizing and budget price.

Discuss on WhatsApp

How this calculator works

Agitator power depends on the liquid density, the impeller speed cubed and the impeller diameter to the fifth power, multiplied by a power number that depends on the impeller shape and the flow regime.

The calculator first finds the impeller Reynolds number to see whether flow is laminar, transitional or turbulent. The power number is then the turbulent value for the impeller plus a laminar term that grows as the Reynolds number falls. This simple blend follows published power curves closely enough for motor sizing.

The motor size adds gearbox losses and your margin, and is rounded up to the next standard IEC motor rating.

Formulas used

Impeller Reynolds number

Re=ρND2μ

Power number (blended laminar and turbulent)

Np=Np,turb+KpRe

Shaft power

P=Np ρ N3D5

N in revolutions per second, D in metres.

Torque and tip speed

τ=P2πN, vtip=πDN

Assumptions and limits

  • Fully baffled vessel with four baffles of one-tenth the vessel diameter, impeller clearance about one impeller diameter off the bottom.
  • Power numbers are typical published values: Rushton 5.0, 45° pitched blade 1.27, hydrofoil 0.3, propeller 0.35, flat paddle 1.7. Actual values vary with blade width and thickness.
  • Multiple impellers on one shaft are assumed spaced at least one impeller diameter apart, so each draws full power.
  • Gas sparging lowers power draw, and solids raise the effective density; adjust inputs accordingly.

Worked example

A 0.8 m pitched blade turbine at 90 rpm in 8 m³ of liquid at 1,050 kg/m³ and 50 cP.

  1. N = 90 ÷ 60 = 1.5 rev/s. Re = 1,050 × 1.5 × 0.8² ÷ 0.05 ≈ 20,160, turbulent.
  2. Np = 1.27 + 45 ÷ 20,160 ≈ 1.27.
  3. P = 1.27 × 1,050 × 1.5³ × 0.8⁵ ≈ 1,477 W, or about 1.5 kW at the shaft.
  4. With 94 percent gearbox efficiency and a 25 percent margin, the motor needs about 1.96 kW, so specify 2.2 kW.
  5. Power per volume ≈ 0.18 kW/m³, suitable for blending and moderate heat transfer.

Frequently asked questions

How do I calculate agitator power?

Use P = Np × ρ × N³ × D⁵, with N in revolutions per second and D in metres. Np is the impeller's power number, which is constant in turbulent flow and rises as flow becomes laminar.

How much power per cubic metre does a reactor agitator need?

Roughly 0.1 to 0.2 kW/m³ for gentle blending, 0.5 to 1 kW/m³ for solids suspension and reactions with heat transfer, and 1 to 2 kW/m³ or more for gas dispersion.

Why does doubling speed need eight times the power?

Because power rises with speed cubed. A small speed increase therefore needs a much bigger motor, while a slightly larger, slower impeller can give the same mixing for less power.

Which impeller is best for viscous liquids?

Above about 5,000 to 10,000 cP, close-clearance anchors or helical ribbons work best because turbines only mix the region near the blades.

Need it designed and built?

SEMCO designs, fabricates and commissions evaporators, ZLD plants, heat exchangers, reactors and vacuum systems in its own factories in Pune and Solapur.

Results are engineering estimates for early sizing and budgeting. Final designs depend on your liquid, site and codes, and are confirmed in SEMCO's proposal. Method reviewed by Jogender Dhayal, Director, SEMCO.